LISUN ELECTRONICS (SHANGHAI) CO., LTD

The EDX-2 series energy scattered X-ray fluorescent spectrometer is realized by analyzing the element characteristic X-ray wavelength and strength of the element emitted by the sample. The elements contained in the sample are determined according to the different elements characteristics of the X -ray wavelength, and the content of the element in the sample can be determined by comparing the strength of the different elemental spectrum. SpecificationEDX-2AEDX-2ACEDX-2ABEDX-2ABCEDX-2TTypeNon -pumping air desktopVacuum desktopWeight50KG55KGTest time200S100SSample cavity size610*320*100mm (L*W*H)510*310*120mm（Non -vacuum）Ф100*70mm（vacuum）Test environmentatmosphereVacuumDetectorSi-pinSDDResolution149 Electronic Volt129 Electronic VoltOutput tube pressure, current50KV/600uA（Can automatically set）50KV/600uA（Can automatically set）Test sample typeSolid, liquid, powderNon -vacuum: solid, liquid, powderPumping vacuum: solidContent analysis range2ppm–99.99%2ppm–99.99%Test itemsTypic Application 1：RoHSTypic Application 1：RoHSTypic Application 1：RoHSTypic Application 1：RoHSTypic Application 1：RoHSTypic Application 3:Coating and Plating ThicknessTypical application 2:alloy analysisTypical application 2:alloy analysisTypical application 2:alloy analysisTypic Application 3:Coating and Plating ThicknessTypic Application 3:Coating and Plating ThicknessMetal test element rangeCan not testAll elements in thePeriodic Table of Elements from 16-S to 92-U are available for alloy analysis (iron, copper, stainless steel,Au (gold),Pt (platinum) , etc)All elements in thePeriodic Table of Elements from 11-Na to 92-U are available for alloy analysis (magnesium aluminum alloy, ore component, iron, copper, stainless steel,Au (gold),Pt (platinum) , etc)Typic Application 1（LISUN Model：EDX-2A、EDX-2AB、EDX-2AC、EDX-2ABC、EDX-2T）: Restriction of Hazardous Substances (RoHS) 1.0 Directive Testing for electronic and electrical products, components, plastics and plastic parts. Click here to download the ROHS 1.0 test report sample. The main test substances in RoHS requirements are as follows: Limit substance Limit content Hg 1000ppm CrVI 1000ppm Cd 100ppm Pb 1000ppm PBBs 1000ppm PBDEs 1000ppm 

RoHS Testing Equipment – Element Analysis – Thickness Gauge (EDXRF)

RoHS Testing Equipment - EDXRF Element Analysis Thickness Gauge

Meet (China) Ltd

- Continuous tone for a good indication
- Warbling tone indicates a fall condition
- Advanced electronics allows clear indication even on noisy&nbsp;
&nbsp; &nbsp;circuits
- 3 colour LEDs show fault location
- Indicates goods and 17 fault conditions
- A built in self-test gives confidence of operation
- True Earth loop impedance test
- Simple loop results : LED colour GOOD, CHECK or URGENT
&nbsp; &nbsp;CHECK
- 30mA RCD operational check
- Tests for reversed Live / Neutral at DNO service cut out
- Incoming supply polarity test
- Simple true polarity test by touching on &#39;POLARITY CHECK&#39;
&nbsp; &nbsp;pad

Advanced Socket Tester

Advanced Socket Tester for comprehensive electrical testing

Truly Electronics Mfg Ltd

Testing Modes: Offers four modes for DC voltage, AC voltage, resistance, and diode testing for comprehensive diagnostics.Display: Features a 2.8-inch color display for clear and easy-to-read results.Wide Compatibility: Suitable for a variety of vehicles, including cars, trucks, SUVs, and motorcycles, supporting both 12V and 24V batteries.High Accuracy: Provides over 99.5% accuracy in testing results.User-Friendly Design: Quick activation and a straightforward interface make operation easy for mechanics and DIY enthusiasts.Versatile Needle Design: Includes long and short needles for testing in tight spaces and standard measurements.Durable Construction: Made from robust ABS and rubber materials for long-lasting use.Smart Chip Technology: Delivers precise testing reports quickly, enhancing diagnostic efficiency.

POWER CIRCUIT PROBE TESTER V-04

POWER CIRCUIT PROBE TESTER V 04 for comprehensive diagnostics

Witschi Electronic Asia Ltd

  It provides perfect test instrument for repair, R&D production and laboratory.  It provides extended test and measurement, allowing professional troubleshootings of quartz watches.  Measuring cycles are largely automated.  Quick and simple setting of parameters.  The chopping level of motor pulses on watches with asservissement will be detected and displayed.  

Testing Instrument For Quartz Watches

AUTOPHIX TECH CO LTD

 OM126  	 NW: 0.26kg (0.57lb), GW: 0.35kg (0.77lb)  

Scanner Reader

Scanner Reader for diagnostic and testing applications

ESD-883D ESD Simulators for IC Testing is specially designed for the characteristics and requirements of the electrostatic discharge immunity test of the Human Body Model (HBM) discharge and the Machine Model (MM) discharge. It can test the electrostatic immunity of semiconductor devices such as LED chips, transistors and ICs. It is designed and manufactured in accordance with the requirements of the following corresponding standards, and fully meets the most stringent electrostatic voltage requirements in the following standards. Discharge ModelInternational StandardsHuman Body Model(HBM)MIL-STD-883 Method 3015 “Test Method Standard for Microcircuits-Electrostatic Discharge Susceptibility Testing”ANSI/ESD STM5.1-2007 “Standard Test Method for Electrostatic Discharge Sensitivity Testing-Human Body Model (HBM)-Component Level”ANSI/ESDA/JEDEC JS-001-2024 “Electrostatic Discharge (ESD) Sensitivity Testing-Human-Body Model (HBM)-Component Level”IEC 60749-26:2018 “Semiconductor devices-Mechanical and climatic test methods-Part 26: Electrostatic discharge (ESD) sensitivity testing-Human body model (HBM)”AEC-Q100-002 “Failure Mechanism Based Stress Test Qualification for Integrated Circuits-ESD HBM Test”EIA/JESD22-A114-A “Test Method for Electrostatic Discharge Sensitivity Testing-Human Body Model (HBM)”Machine Model(MM)ANSI/ESD STM5.2-2013 “Standard Test Method for Electrostatic Discharge Sensitivity Testing-Machine Model (MM)-Component Level”IEC 60749-27:2012 “Semiconductor devices-Mechanical and climatic test methods-Part 27: Electrostatic discharge (ESD) sensitivity testing-Machine model (MM)”AEC-Q100-003 “Failure Mechanism Based Stress Test Qualification for Integrated Circuits-ESD MM Test”EIA/JESD22-A115-A “Test Method for Electrostatic Discharge Sensitivity Testing-Machine Model (MM)”Characteristic:• Color LCD touchscreen, easy to operate.• Output voltage with high accuracy and stable performance• Intelligent programmable high-voltage power supply, high-voltage over-voltage, over-current, short-circuit protection• With self-diagnosis function, can intelligently judge abnormal high voltage output• Cost-effective: The main components are all imported, with high accuracy and low failure rate. Specification: Output voltageHuman Body Model（HBM）Machine Mode (MM)0.05~8kV±5％50~800V±5％Output polarityPositive, Negative or Automatic switchingTrigger modeSingleSingle dischargeCountDischarge according to the set discharge timesOtherHost self-triggeringDischarge modeHBM and MMDischarge Interval1~99sDischarge Number1~999Discharge Capacitance100pF±10％200pF±10％Discharge Resistance1500Ω±10％0Ω±10％Working PowerAC 100~240V, 50/60Hz, 300WNote: ESD-883D can share a host withESD-CDM Charged Device Mode (CDM) ESD Testing for IC to test HBM, MM and CDM at the same time (LISUN model: ESD-883D/ESD-CDM) 

HBM/MM ESD Simulators for IC Testing

This is a watch testing machine that can print the report. It can test the quality and stability of the watch. It is accurate and fast, so it is widely used by watch manufacturers.    Fast overview of quality & stability  Effective and professional testing of mechanical watches  Digital LCD display and printer  

Watch Testing Machine

Watch Testing Machine for quality and stability assessment

The JL-X includes the following water proof IP codes: IPX1, IPX2, IPX3, IPX4, IPX5, IPX6, IPX7 and IPX8 (Refer to page 51 ofIEC 60529). It is widely used in the authentication test organization for the products such as electrical &amp; electronic products, LED luminaires as well as in the relevant quality control department for the waterproof detection of the enclosures protection grades. Standard:IEC 60529:1989 +A1:1999 +A2：2013 “Degrees of protection provided by enclosures(IP Code)”IEC 60598 “Luminaires – Part 1: General requirements and tests”IEC 60335 “Household and similar electrical appliances – Safety – Part 1: General requirements”IEC 60034-5 “Rotating electrical machines – Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) – Classification”GB 7000.1 “Luminaires-Part 1：General requirements and tests” The whole JL-X waterproof test system includes:• Drip Box (JL-12): The drip box meets the test requirements of IPX1 and IPX2 in Clause 14.2.1-14.2.2 and Figure 3 of IEC 60529:1989 +A1:1999 +A2：2013. The drip box size is 800x800x45mm (LxWxH). The diameter of drip hole is 0.4mm. The distance between drip holes is 20mm. It can test samples over 150kg. •Swing Pipe Water Spray Test Equipment (JL-34):It meets the test requirements of IPX3 and IPX4 in Clause 14.2.3-14.2.4 and Figure 4 ofIEC 60529:1989 +A1:1999 +A2：2013. The radius of oscillating tube is 1meter (Any other size is also available). The internal diameter of the tube is 15mm. The sample turntable diameter is 1000mm (Other sizes are optional according to the diameter of the oscillating tube), and the height is adjustable. It includes a water tank. The rotation speed is 1~5rpm which can be set and controlled by PLC panel. • Spraying Nozzle and Splashing Water Hand held Test Device (JL-34S):It meets the test requirements of IPX3 and IPX4 in Clause 14.2.3-14.2.4 and Figure 5 ofIEC 60529:1989 +A1:1999 +A2：2013• Water pressure regulation requirement: The water pressure is adjusted to achieve the specified flow rate, and the required pressure range is 50 kPa to 150 kPa.• Test duration requirement: The test duration is 1 minute per square meter of the calculated surface area of the shell (excluding any mounting surface), and the minimum test time is 5 minutes.• The JL-34S includes the following: a pressure gauge, an 8m long water pipe and a Sprinkler with a 5mm Spray Nozzel. • Waterproof Jet Test Device (JL-56): It meets the test requirements of IPX5 and IPX6 in Clause 14.2.5-14.2.6 and Figure 6 of IEC 60529:1989 +A1:1999 +A2：2013. With a 780*580*1100mm size water tank, the nozzle diameter is ф6.3mm (IPX5 waterproof test ) and ф12.5mm (IPX6 waterproof test). The water flow is 12.5 ±0.625L/min for IPX5 and 100 ±5L/min for IPX6  

IP Waterproof Test Equipments

IP Waterproof Test Equipments for comprehensive waterproof testing.

- Non-trip RCD testing method
- Test lead nulling point
- Six insulation check levels (Plus correct output check)
- Five continuity check levels (Plus correct output check)
- Two loop impedance test points plus local loop
- Five checks covering 30mA and 100mA RCD&#39;s
- Checks RCD over current test
- Test leads for resistance and insulation checks
- Calibration certificate with measured values
- Tough drop-proof watertight case
- Operating voltage : 230V (Mains supply)

Professional Calibration Check Box

Professional Calibration Check Box for RCD and insulation testing

Goldsun Electronics Co., Ltd.

   These are remote cable tester, pro lantester 2210 and digital multimeter.   Digital multimeter has a black cable and a red cable.   All three products are in plastic case with control buttons on the front.  

Networking Specialized

Networking Specialized remote cable tester and digital multimeter

 	 Touch panel 	 Digital multimeters &amp; cable testers 	 The unique and smart meter design 	 3.5&quot; TFT-LCD (320 x 240)pixels colors 	 Back light + touch panel 	 Multi-meter 	 Cable tester 	 LED lighting 	 Auto power off  

All-In-One DMM & Cable Tester

*Touch Panel.
*Digital Multimeters &amp; Cable Tester.
*The Unique and Smart Meter Design.
*3.5 &quot;TFT-LCD(320*240) Pixels Colors.
*Back Light+Touch Panel.
*Multi-All-in-one DMM &amp; Cable Tester.

TCT-910 All-in-One DMM & Cable Tester

Shanghai Joysun Auto Technology Company Ltd.

 EDX-B6T XRF COATING THICKNESS ANALYZER

Dongguan Habotest Instrument Technology Co., Ltd.

Habotest HT107B Socket Tester With Voltage Test and RCD USA plug  Voltage Range:AC 48-250V    GFCI Test5mA    Voltage Measurement  48V-250V/45-60Hz    LCD Display    Backlight    Socket Connection Dtection:  CORRECT    OPEN GROUND    OPEN NEUTRAL    OPEN LIVE    LIVE/GRD REVERSE    LIVE/NEU REVERSE    LIVE/GRD REVERSE, MISSING GRD  Weight:Approx.50g  Size:65*62*58mm  Saftey Rating:EN61010-1,-2030;EN61326-1,CATII 300V   

socket tester/outlet tester/voltage tester

socket tester outlet tester voltage tester

The LS9955/LS9956Automatic Safety Test System (electrical safety analyzer) combines the following functions: Withstand Voltage Test (AC / DC), Insulation Resistance Test (IR), Leakage Current Test (LLC), Grounding Resistance Test (GR) and Power Test (LS9956 includes Power Test, LS9955 does not include Power Test). The equipment is mainly used for lighting fixtures, household appliances and motor tools safety test on the production line or in the R&amp;D laboratory. Standard:IEC/EN 60335-1:2023/GB 4706.1-2024 “Household and similar electrical appliances – Safety – Part 1: General requirements”UL 60335:2022 “Standard for Safety of Household and Similar Appliances, Part 1: General Requirements”IEC 60598:2024/GB 7000-2023 “Luminaires – Part 1: General requirements and tests”IEC 60950:2020 “Information technology equipment Safety –Part 1: General requirements “IEC 62368-1:2023/GB 4943-2022 “Audio/video, information and communication technology equipment – Part 1: Safety requirements”IEC 60601-1 3.1:2012/ GB 9706.1-2020 “Medical Electrical Equipment – Part 1: General Requirements For Basic Safety And Essential Performance” Specification:• Remote control device and can control by software (Optional)• Display all setting parameters and testing results in the same big LCD screen• PASS/FAIL limit values can be set.If the object fails the test, there will be a light/sound alarm• Test mode is programmable; 50 groups settings are available, 8 test steps per group• Quick discharge. Support 50Hz and 60Hz frequency; Electric safety wall detecting feature• The LS9955 can test Withstand Voltage (AC/DC), Insulation Resistance (IR), Leakage Current (LLC) and Ground Resistance (GR)• The LS9956 can test Withstand Voltage (AC/DC), Insulation Resistance (IR), Leakage Current (LLC), Ground Resistance (GR) and Power Withstand Voltage Test (AC/DC)Insulation Resistance Test (IR)Voltage RangeAccuracyCurrent RangeIR RangeAccuracyVoltage Range100~4000V± (5%+3V)AC: 0.10~20.00mADC: 0.10~12.00mA1.00~2000MΩ5% + 0.5MΩDC100~1000VLeakage Current Test (LLC)Grounding Resistance Test (GR)LLC RangeAccuracyVoltage RangeGR RangeAccuracyOutput Current0.10~20mA± (0.3%+5uA)AC10.0~300.0V0~600mΩ± (5%+2mΩ)AC1.00~30.00APower TestVoltageCurrentPowerPFAccuracyTest Time10~300V0.010~20.00A1.0~6000.0W0.2~1.0Class 0.50~999.9sP.S. The LS9955/LS9956 of Leakage Current Test (LLC) needs to work with LISUNITEU-SP1KS or ITUS-SP1KS Isolation Transformer (The Output is 1.06times of the input). The LS9955/LS9956 of Leakage Current Test (LLC) and Power Test need to work with LISUNLSP-1KVARC orLSP-1KVAS AC Power Supply. 

Automatic Safety Test System

Automatic Safety Test System for electrical safety analysis

EDX-v61G XRF GEMSTONE TESTER RUBBY TESTER

EDX v61G XRF GEMSTONE TESTER RUBBY TESTER

EDX-B9 XRF GOLD TESTER GOLD SILVER ANALYZER

EDX B9 XRF GOLD TESTER GOLD SILVER ANALYZER

Guangzhou Duoyi Electronics Ltd.

Showing is an electrical testing instrument with multi functions. Professional and accurate, this tester provides the auto ranging, data hold and LCD backlight. Together with a well-designed packaging box, this tester is perfect for various electronic product testing. 	 Ground resistance measurements from 0.01ohm to 2000ohms with 0.01ohm resolution. 	 Product net weight approx. 900g.&nbsp; 	 Measure insulation resistance to 2000M ohms. 	 Test voltage 250V, 500V, 1000V. 	 AC voltage measurement to 600V. 	 Check phase sequence and phase status. 	 Auto ranging, data hold, LCD backlight. 	 Low battery warning. 	 Complete with test leads, auxiliary earth bars, phase wire, heavy duty carry case and eight AA. 1.5V dry cells. 	 Earth resistance: 0~20/200/2000&Omega; &plusmn;(2%+5). 	 Testing voltage: 250/500/1000V. 	 Insulation resistance: 0.1~2000M&Omega; &plusmn;(3%+5). 	 Phase rotation check: yes. 	 AC V 700V &plusmn;(2%+5). 	 Auto range: yes. 	 Function symbol display: yes. 	 Data hold: yes. 	 Low battery warning: yes. 	 Max. displays 1999. 	 LCD backlight yes. 	 Power AA1.5V x 8.  

Multi Function Tester

Multi Function Tester for accurate electrical measurements

EDX-B3T XRF COATING THICKNESS ANALYZER

Dongguan Watchmaker Technology Co., Ltd.

Automicaled vacuum watch waterproof tester Testing for Waterproof Performance of Watches Fully automatic measurement, with multiple test programs, capable of detecting watch leaks through leak testing, requires an air compressor, equipped with a built-in printing system Testing Range:﹣0.7bar~+10bar      

2TH Automicaled vacuum watch waterproof tester

automicaled vacuum watch waterproof tester

 	 Designed in UK 	 Displays PFC/ PSC at same time as Loop reading 	 250/ 500/ 1000V insulation test with auto discharge 	 Test leads auto-null for continuity mode 	 RCD auto test mode for 30mA RCDs 	 RCD ramp test function 	 End of line calibration certificate included 	 Hand-free mode controlled by separate button 	 Single rotary dial for function selection 	 Mains polarity test 	 Colour coded lead set with clips and prodes 	 Battery powered: 4XAA (R06/ LR06)  

Professional Multifunction 5 in 1 Tester

Mecca Electronics Co Ltd

Auto Testing ~ production lines / PCB Assembly Services - we welcome Box Build and PCB Assembly full turnkey projects, from pure contract manufacturing to ODM. We manufacture products according to customer specifications, approved material and processes. 

Auto Testing ~ production lines

EDX-B3 XRF GOLD TESTER GOLD PURITY TESTING MACHINE

EDX B3 XRF GOLD TESTER GOLD PURITY TESTING MACHINE

The EFT61000-4 EFT immunity tester is especially designed according to the characteristics and requirements of EFT measurement and it is an ideal disturbance source of EMS measurement. It has fine performance, such as high stability, high reliability, easy to use etc. EFT61000-4 has LCD touch screen in both English and Chinese. Standard:IEC 61000-4-4/EN 61000-4-4 “Electromagnetic compatibility (EMC)Part 4-4: Testing and measurement techniques — Electrical fast transient/burst immunity test” Specification: LISUN ModelEFT61000-4EFT61000-4AEFT61000-4-32AEFT61000-4A-32AEFT61000-4-100AEFT61000-4A-100AOutput voltage0~5kV0~6kV0~5kV0~6kV0~5kV0~6kVPulse frequency1kHz~1,000kHz Continuously adjustablePolar pulsePositive/negative, positive and negative automatic alternationInternal resistance50Ω ±20%、1000Ω ±20%Pulse rising time5ns ±30%Pulse width (at 50Ω)50ns ±30%Pulse width (at 1kΩ)35ns～150nsPulse length0.01ms~20msPulse period100ms~500msTest time1s~9999sTest functionSet the test mode or IEC standardCoupling/decoupling networkBuilt -in CDN, 16A, 3 phase/5 linesBuilt -in CDN, 32A, 3 phase/5 linesExternal CDN, 100A, 3 phase/5 linesWorking power supplyAC220V (110V optional) ±10%, 50/60Hz 

My Sourcing

Unfollow this supplier?

Unfollow this supplier?