Linkchamp Co Ltd

DC to DC Buck/Boost Converter 12/24/48V 10~50A https://www.dc-ac.com/product/new 10~50A Intelligent DC-DC® Boost Converter 12V to 24V 10~40A Intelligent DC-DC® Buck Converter 24V to 12V 5~15A Intelligent DC-DC® Buck Converter 48V to 12V 5~15A Intelligent DC-DC® Buck Converter 48V to 24V 75W Intelligent DC-DC® 4-IN-1 Buck-Boost Converter 10~60V to 12V 

DC to DC Buck/Boost Converter 12/24/48V 10~50A

DC to DC Buck Boost Converter 12 24 48V 10 50A

Manson Engineering Ind'l Ltd

This new series of non-isolated digital DC-DC Step Down Converter with micro-processor control for fine adjustment of output voltage to optimally suit the loading condition. The 3 digit LED display shows: output voltage, current, operation mode and fault status It is further equipped with 4 special features:1. A full powered 2 Stage Charger with 14.3V Bulk &amp; 13.6V Float Charge.2. A Remote Control terminal that turns off the converter when the Ignition is switched off, preventing discharging of starter battery. This terminal can be used with other external on-off switch set up.3. A Remote Voltage Sensing at load point to ensure accurate output voltage for distant load/ battery to ensure optimal operation.4. An independent, separate and always-on output (0.5A 13.8VDC) for essential devices such as security system that requires a permanent dc source. It can also be used for the remote on off switch. Micro-Processor Control with switching mode power design.19 -36VDC Input with adjustable Output 12 to 15VDC in 0.2V step.3digit LCD display for Current, Voltage, Operation Mode and Protection Diagnosis .2 Stage full powered charger mode with 14.3V bulk and 13.6V float charge.Remote Voltage Sensing for optimal powering of distant load or charging battery.Remote control terminal auto On/ Off with ignition control and other external on/off switch.An independent always-on auxiliary output (0.5A, 13.8V) to power critical electronic device or the remote on off switch.8 fail- save protections of which 6 with diagnostic code at the LED display.Input under voltage warning has remote alarm connection.Optional accessory AVS-5025 vibration sensor to automatically control the On-Off charging operation without touching the car’s electrical system at all. This is ideal for non-technical users.Extensive ProtectionMulti-stage software based safety device with early warnings of impeding shut down faults for low input voltages. Most of the protections are self recoverable when conditions return to normal with 6 diagnostic code on the LED display. Input under voltage (self recoverable)Input over voltage (internal fuse)Output over voltage (self recoverable)Output short circuit (self recoverable)Output overload (self recoverable)Output (battery) reversed polarity (internal fuse)Over temperature (self recoverable)Fan Stuck Fault (jammed object removed -&gt; self recoverable)

SDC-5300 Series Programmable DC-DC Converter and Battery Charger

SDC 5300 Series Programmable DC DC Converter and Battery Charger

 3-Stage ChargingSupports STD, GEL, AGM, CAL, LiFePO4Supports LC Wire for Charging Current AdjustmentCompatible with Both Conventional and Smart AlternatorsInput &amp; Output Fully IsolationIntelligent Temp &amp; Load Cooling FanMulti Pre-Alarm &amp; Shutdown Alarm Protections: Battery Type Detection / Polarity Reverse / Low Voltage Short Circuit / Overheat / OverloadAluminum Housing100% Made in Taiwan  

DC-DC Charger 12V->12V 30A/60A for Lead-Acid and LiFePO4 Batteries

DC DC Charger 12V 30A 60A for Lead Acid and LiFePO4 Batteries

Jiewei yida electronic technology Co., Ltd.

switching power supply

深圳依炮爾科技有限公司

 	 Smart IC control, switch freely between charging and 	 discharging mode. 	 Built-out LiFePO4-battery, flexible, safe, stable and long lasting. 	 Self-testing and self-diagnostic function optional. 	 Constant current for 2/4/6W max output power.  

Constant Current LED Emergency Inverter

Constant Current LED Emergency Converter EPE ED2

洋鑫科技股份有限公司

Universal AC input 90~264VAC. Constant Current Mode with multiple current selectable by DIP switch. Dimming method : DALI/DALI-2 or PUSH dimming. Active PFC design. Protections: OLP/ SCP. Cooling by free air convection. Standby Power Consumption &lt; 0.5W. Wide voltage range from 10V to 42V. Suitable for high brightness light-emitting diode products. 

Constant Current LED Driver(CCP010P-42CD-TA1)

Constant Current LED Driver CCP010P 42CD TA1

Keytec Technology Co Ltd

a simple product, DALI2 to 0-10V, we have DT5 and DT8, max power consumption is 4mA. contact us for more detail. 

DALI TO 0-10V 

深圳邁睿智能科技有限公司

1) Constant power output LED emergency power supply, wide output voltage range. 2) Multiple protection function: battery over charge , deep discharge, output overload and short-circuit protection. 

LED Emergency Converters

LED Emergency Converters for reliable emergency power supply

寧波海曙浩然燈具有限公司

 	 15W 12V DC Constant voltage IP20 	 BELD-1512VL  

LED Driver

LED Driver - 15W 12V DC Constant voltage IP20

EMTRONS TECHNOLOGIES LTD

Mini LED Emergency Converter

浙江聯龍電子電器有限公司

LLD41/030AC Input voltage: 220 to 240V AC Output voltage: 110 to 120V AC Maximum power: 30W Input plug: ST Packing: individual colored gift box  LLD66/100AC Input voltage: 220 to 240V AC Output voltage: 110 to 120V AC Maximum power: 100W Input plug: with cable Packing: individual colored gift box 

AC/AC CONVERTERS

Zhuhai Ltech Electronic Technology Co., Ltd

High performance that ordinary driver hard to achieve. 60000:1 wide dimming range, 0-100% full dimming range. Fully digital circuit design, built-in high-performance MCU. T-PWM dimming technology smooth and flicker-free. 3-54V wide range, 8 options of current,ISET terminal can set any current value.

DALI Intelligent Dimmable LED Driver 

深圳市奧特瑪科技有限公司

DC DC LED Driver 

DC DC LED Driver with 200W power efficiency.


 Features&gt;&gt;  	 Compatibility with DALI standard (IEC62386 Part 102 &amp; Part 206) 	 DALI signal line regardless of pole 	 Screw-less connector, easy to install 	 Selectable output for PWM / DC 0-10V / DC 1-10V 	 Selectable dimming curve for logarithm or linear 	 Build-in Relay to turn ON/OFF driver completely 	 3 years warranty   Specifications&gt;&gt; 

 Electrical Specification: &nbsp; &nbsp; &nbsp; MIN. &nbsp;TYP. &nbsp; MAX. 
Input Voltage(VAC): &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;90 &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;&nbsp;290
Power Consumption(W): &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 1.6 &nbsp; &nbsp; &nbsp; 3
 DALI Bus Current Consumption (mA): &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;2
Suitable Electric Wire (AWG): &nbsp; &nbsp; &nbsp; &nbsp;22 &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;16
PWM Frequency(Hz): &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;500
PWM High Level Voltage (VDC): &nbsp; &nbsp; &nbsp; &nbsp;9.5 &nbsp; &nbsp; 10 &nbsp; &nbsp; 10.5
PWM Low Level Voltage (VDC): &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;0
PWM Output current sourcing (mA): &nbsp; &nbsp;-60 &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 60
DC 0/1-10V output accuracy: &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &plusmn;3% 
 DC Output current sourcing (mA): &nbsp; &nbsp; &nbsp;-5 &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 60 

 Other Functional Description: 
Compatibility DALI Standard: IEC62386 Part-102 &amp; Part-206
DALI Input reversed protection: Yes
Number of output channel: 1
Output channel short protection: Yes
Weight:  100g&plusmn;10% 
Dimensions (L&times;W&times;H): 150&times;40&times;28 mm
Operating Temperature Range: -20~+40&deg;C
Relay Switch (1 channel ): 2A /Max inrush current 70A
&nbsp;

LED DALI Interface Converter

LED DALI Interface Converter with multiple output options

Extra Compact Universal LED Emergency Converter

萬保剛電子集團有限公司

Claf AC/DC Power Suppliers , DC/DC Converters 

Claf AC/DC Power Suppliers

恒昌(寧波)照明電器有限公司

Characteristics: Rated Input Voltage: AC220-240V 50HZ( Power factor measured at AC230V and full load) Model No.     Constant Output Voltage    Load     λ        Ta        Tc            L*W*H       Approval GPD20-12VF         DC 12V            0-20W   0.5     -20-45℃    85℃       167*45*14.5mm    TUV GPD20-24VF         DC 24V            0-20W   0.5     -20-45℃    85℃       167*45*14.5mm    TUV  Features: *Independent driver for constant voltage LED light *5 way socket on secondary side directly for easy connection *Terminal block for quick connection *SELV output *Open sircuit, short sircuit, over load and over temperature protection *Auto restart after fault conditions removal *Efficiency ≥ 83%（AC 230V, full load）  

GPD20-12VF

fix in STUCCHI 9519-166. with teRminal and DIP 

48V input DALI2 DT8 Constant current LED driver

Optimal Efficiency 92% with Digital ControlThe high power conversion efficiency allows quiet and cooling running of the charger and can provide continuous full loadoperation at 40°C ambient temperature. Designed to cover old and new types of car alternatorsThe SBC-6104 are designed to address to the issues of wide swing of output voltages from the smart alternator, braking regenerative EURO 5/6 vehicles in fully charging the house battery. They are also suitable for use with distant house battery. The charger Booster provides fast safe charging profiles for 4 types of lead based and 2 types of Lithium FePO4 batteries. Multistage ChargingThis is a select (battery type) and forget charger designed for fast accurate and safe recharge of your deep cycle house battery banks. The (digital control) smart multistage charging enables the charger to be connected permanently to your battery banks without the worry of over charging or drying out the electrolyte. Lead acid based BatteryA 3 Stage Bulk, Absorption &amp; Float charging profile for 4 types of lead acid based battery with maximum constant charging current at the Bulk Stage and a Constant Voltage with decreasing charging at the Absorption Stage and a reduced voltage Float Charge for maintenance when battery is full. LiFePO4 (LFP) BatteryA 2 Stage charging is specially for 2 types LiFePO4 battery and charging current stops at the end of Absorption stage. Three charge control methods: Ignition Control:Charger starts charging only when ignition is on and stops charging when Ignition is off.This is the recommended control as it is safer and allows for large input voltage range. Input Voltage Control:This is for non-intelligent or older type alternators with sufficient high &amp; uniform voltage.Charging is cut off easily due to high threshold voltage to protect the starting battery. Vibration Sensor Control:Charger starts charging when repeated vibrations are detected and stops charging when no vibration is detected for over 2 minutes.The built-in vibration sensor makes it possible to use the charger by just connecting to the starter terminal without touching the car’s electrical/electronic wiring thus avoiding any possible excuse for revoking the car’s warranty.Features 480Watt power conversion efficiency &gt;90%.6 selective charging profiles suitable for charging for the most lead acid &amp; Lithium FePO4 batteries.Supplied with a remote Battery temperature sensor to ensure precise and safe charging in large temperature variation.3 types of operation control to choose for specific situation.Alarm signal (fault or not charging) available to integrate with your system.Thermostatically speed control Fan.Protections:Self recoverable Input under Voltage protection.Self recoverable Input over Voltage protection.Self recoverable Output over Voltage protection.Self recoverable Overcurrent protection.Self recoverable Charger over temperature protection. 

SBC-6000 Series DC-DC In-Car Charger for Lead and LFP Batteries

SBC 6000 Series DC DC In Car Charger for Lead and LFP Batteries

CUPOWER EUROPE GMBH

Product Features Isolated adjustable power color temperature LED driverSupports DALI-2, push DIM control , push CCT controlUsable as DT6 (2-channel) or DT8 (tunable white) driverCurrent adjustment via NFCSupports i-Data function(DALI part 251,252,253)Output current 500…1050mAMax output power 44WDC emergencyFlicker-freeCurrent output default value 100%For luminaires with protection class l, llDescriptionConstant current driver with wide operating windowsSupports DALI-2, push DIM and push CCTSupports NFC readers for precise setting and control of multiple functionsSupports two independent DT6 or one DT8 outputSmooth colour temperature setting and dimming with dimming range 1-100% (amplitude dimming)Equipped with i-Data (30W, 44W, 60W): enabling data management according to DALI parts 251, 252 and 253The DC emergency mode adjusts the current to 15% by default (adjustable), applies to 30 W, 44 W, 60 W versionsLoop through connection comply with 2.5 mm² engineering cable entry specificationsStandby power consumption ≤ 0.3 W (30-60 W), &lt; 0.5 W (20 W), meets ErP energy efficiency certificationPacking unit programming: configure a large number of drivers in parallel via NFC For more information, please visit the product page on our official website： https://cupower.com/theproducts_7/ID-CCCB-44-230-500-1050-DT8-NFC-FV1.html 

DALI DT8, Built-in & Independent LED Driver, 44W, 500-1050mA, Flicker-Free, NFC-Control with DC Emergency

DALI DT8 LED driver with NFC control and DC emergency

Characteristics: Rated Input Voltage: AC220-240V 50HZ( Power factor measured at AC230V and full load) Model No.     Constant Output Voltage    Load     λ        Ta        Tc            L*W*H       Approval GPD15-12VF         DC 12V            0-15W   0.5     -20-45℃    80℃       132*50*13.5mm    TUV GPD15-24VF         DC 24V            0-15W   0.5     -20-45℃    80℃       132*50*13.5mm    TUV  Features: *Independent driver for constant voltage LED light *Terminal block for quick connection *Class II protection against electric shock from direct and indirect contact *SELV output *Open sircuit, short sircuit, over load and over temperature protection *Auto restart after fault conditions removal *Efficiency ≥ 75%（AC 230V, full load） 

GPD15-12VF

GPD15 12VF LED driver for constant voltage applications

深圳市研碩達科技有限公司

 DS series super compact waterproof power supply       FAQ Q : Are your factory ?A : Yes, we are factory.  Q : How to place order ?1. Customer send us an inquiry and share your contact information. 2. Confirm all details such as order quantity, price, lead time, payment term etc.3. Our sales team send the Proforma Invoice with company seal.4. Customer make the payment for deposit and send us Bank receipt.5. Inform the clients that we have got the payment,and will arrange the production according to your request, inform the estimated time.6. Will inform the customer about the goods ready date.7. Clients make payment for balance, we make shipment according to customer's requirement.  For more details please Enquiry or Chat NOW us! 

DS series mini high PFC led driver 30-500w DC12V/24V

Displayed here is a LED driver with dimmable function. It has a rectangular shape casing with electrical information shown on the exterior. This LED driver is a reliable power supply for LED lighting systems. 	 Rated power: 11W. 	 Input voltage: 220-240V 50/60Hz. 	 Output current: 350mA. 	 Dimmable: yes. 	 Complied with safety and EMC standard. 	 Rectangular shape. 	 Electrical information shown on the exterior. 	 Easy to install. 	 Long working life. 	 Reliable power supply for LED lighting systems.&nbsp;  

LED Driver with dimmable function and reliable power supply

Product Features Isolated adjustable power color temperature LED driverSupports DALI-2, push DIM control, push CCT controlUsable as DT6 (2-channel) or DT8 (tunable white) driverCurrent adjustment via NFCSupports i-Data function (DALI part 251, 252, 253)Output current 700…1500 mAMax. output power 60 WDC emergencyFlicker-free, dimming range 1%...100% (amplitude dimming)Current output default value 100%For luminaires with IEC protection class l, llAnti-glow Description Constant current driver with wide operating windowsSupports DALI-2, push DIM and push CCTSupports NFC readers for precise setting and control of multiple functionsSupports two independent DT6 or one DT8 outputSmooth colour temperature setting and dimming with dimming range 1-100% (amplitude dimming)Equipped with i-Data (30W, 44W, 60W): enabling data management according to DALI parts 251, 252 and 253The DC emergency mode adjusts the current to 15% by default (adjustable), applies to 30 W, 44 W, 60 W versionsLoop through connection comply with 2.5 mm² engineering cable entry specificationsStandby power consumption ≤ 0.3 W (30-60 W), &lt; 0.5 W (20 W), meets ErP energy efficiency certificationPacking unit programming: configure a large number of drivers in parallel via NFC For more information, please visit the product page on our official website： https://cupower.com/theproducts_7/ID-CCCB-60-230-700-1500-DT8-NFC-FV1.html 

我的採購

確定要取消關注此供應商？

確定要取消關注此供應商？